Water Damage Repair in Beloit WI 53511

Locally Owned & Operated


Looking for the right Water Damage company for your home or property? Since 1980 we have been providing Water Damage services to the Beloit area.

(877) 534-6458

(Beloit WI 53511) �” 

Step 1: Find the Water Leak   Sometimes it will be obvious that you have water leaking either behind your walls or onto the ceiling from above. The ceiling or walls may show visible signs of moisture, dripping water, or signs of failing structural integrity. Ceiling drywall panels may sag or crumble under the weight of water that saturates the naturally porous gypsum material. Other times, you may notice small ECO Disaster Services Beloit WI 53511 signs like coffee-colored stains that may expand over time. Before making any repairs, you need to find the source of the water leak. This can be frustrating, but if you don’t fix the source of the water problem first, repairs will do you no good. Whether it’s a leaky roof, a broken pipe or leaking toilet, it can sometimes be difficult to locate the source. Water can travel far from Beloit WI 53511 the leak and cause damage somewhere you wouldn’t expect it. This means you have to do some exploration and investigation. Remove damaged drywall so that you can better see where the leak is coming from (see Step 2) and so you can dry out the water-damaged space. Safety Alert! Depending on how long the leak has gone unchecked, there may be mold present in or on the drywall. Some mold, ServiceMaster ... Beloit WI 53511 such as “black mold”, is better off remediated by professionals because it may be very toxic when present in large amounts. If you do have large amounts throughout an interior area �” anywhere around 10 sq. ft. �” call a professional to have it removed. If only a small amount of mold is present, you can safely remove it or the moldy drywall yourself, if you take precautions. Wear gloves, Beloit WI 53511 safety goggles and a dust mask so that you don’t breathe in the mold. In some serious cases where there is severe water damage, you may need to call in a professional contractor to repair the source of the leak or to repair the damaged walls or ceiling. Step 2: Remove Water-Damaged Drywall   Before starting, put down drop cloths or tarps to catch all the drywall pieces, dust and Beloit WI 53511 debris created by removing the damaged drywall. This will make cleanup easier and protect surfaces from the dust and mess. Check the drywall to see how much damage has been done. Heavily water-infiltrated wallboard will sag from ceilings or crumble to the touch. Remove all compromised drywall by hand or use the claw end of a hammer or a wrecking bar to remove it. If drywall panels only show water Beloit WI 53511 stains but aren’t structurally compromised, they may be repairable by cutting out the damaged portion. When cutting out around the damaged area, use a keyhole saw to cut the hole into a square or rectangular shape. You can then make a patch with another piece of drywall for the repair. Safety Alert! Step 3: Make Repairs   If you are patching the wall or ceiling, measure the square or rectangular Beloit WI 53511 area of the wall that you cut out from Step 2. Use these dimensions to cut a replacement piece of drywall to fit, 2″ longer and 2″ wider than the hole. Lay the replacement piece of drywall on a flat surface with the backside facing up. Measure in 1” from all four edges and draw a line using a pencil. This should form a shape the size of the hole. Beloit WI 53511 Using a straight edge and utility knife, cut through the backside paper and the drywall gypsum, but not the front-facing layer of paper. Using a putty knife, peel away only the backside paper and gypsum layer. Be careful not to tear the front-facing paper. Helpful Tip If the patch isn’t a perfect fit, place it against the hole and trim to size with a utility knife. Holes bigger than 6″, Beloit WI 53511 up to 12”, require a slightly different process because the patch needs more support. Using a drill, create two small holes through the piece of replacement board. Feed a piece of string through and tie both ends to the middle of a stick. Allow for about 8″ of string between the board and the stick. The “stick side” of the board will be the front. The stick will be used Beloit WI 53511 to hold the patch in place. Twist the stick to apply pressure to the rear of the board. This will steady it in the hole. Apply a smooth coat of cement adhesive around the edges. Insert the patch into the hole and position it so the cement adhesive firmly grips the solid area around the rear of the hole. Turn the stick clockwise, twisting the string and increasing pressure against Beloit WI 53511 the patch board at the rear of the hole. This will hold the board firmly in place until the cement adhesive dries. Helpful Tip To make it easier to insert the wallboard material through the hole, be sure to hold it at an angle. If you’re working with a smaller hole (up to 6″), apply a thin layer of joint compound around the hole. Place your patch into the hole. Beloit WI 53511 Using a putty knife, work the paper edge down into the compound. Feather the edges of the compound and allow it to dry. Sand lightly with a fine-grit sandpaper and apply a second layer of joint compound to finish the repair. For larger holes (between 6″ and 12″), allow the cement adhesive to thoroughly dry then fill in the area with joint compound. Smooth out the area then let the Beloit WI 53511 patch dry thoroughly. Helpful Tips You may need to apply two or three layers of joint compound to build up the patched area. Always allow each layer to dry before applying another. Let the stick and string remain where they are during the patching process. You can remove both just before the material dries. When the area is completely dry, sand off any high spots using fine-grit sandpaper and a Beloit WI 53511 sanding block. Damaged areas larger than 12 square inches may need a complete replacement panel installed because large pieces of drywall need to be anchored to wall studs or ceiling joists. It depends on where the damage is located on the wall or ceiling and how you had to cut it out. For example, if the space where you removed the damaged drywall exposes studs or joists where it will Beloit WI 53511 be possible to secure a patch by screwing it into the stud or joist, you can do that. If not, you may have to replace the whole drywall panel. To replace the whole sheet, remove the damaged drywall completely, down to the studs. Remove the drywall screws that anchored the old sheet to the studs using a power drill. If there was a lot of water damage, this should be Beloit WI 53511 fairly easy; the old drywall will most likely crumble away. Measure the height and width of the space you’re repairing so that you know how much new wallboard you need. If you need custom-sized panels for an irregularly shaped repair, use your measurements to cut a patch to fit, using a utility knife or drywall saw. Align your new panel with the wall studs and then secure the panel to Beloit WI 53511 the studs with drywall screws and a power driver. Use joint tape to cover the seams where each panel meets. Then apply joint compound over the tape, using a putty knife. Let the compound dry for the time specified by the manufacturer and then sand the compound with fine-grit sandpaper until the seams are flush with the drywall panels. Helpful Tip Enlist someone as a helper if you’re putting in Beloit WI 53511 whole drywall panels or working on ceiling repairs. Drywall can be heavy, and trying to keep it steady while fastening it in place can be challenging. Step 4: Prime and Paint   Apply True Value EasyCare® Ultra Premium Interior Primer/Sealer with a large paintbrush or roller applicator. Make sure you cover the entire surface of the wall.  Safety Alert! Open windows to make sure you prime and paint in a Beloit WI 53511 well-ventilated area. Pour True Value EasyCare® Ultra Premium Interior Paint into a paint tray and coat your roller or paintbrush. Paint widthwise in 6-ft. square sections, using a zigzag pattern of overlapping “W” strokes. Move from right to left, then left to right, spreading evenly with vertical strokes. To ensure even coverage, use light strokes to re-roll across the ceiling and paint from the bottom to the top of each Beloit WI 53511 wall. If your paint has a flat finish, you don’t need to blend. Otherwise, to blend, paint over the entire surface (for very large areas, do two square sections at a time) with one-directional, overlapping, non-diagonal strokes once again. Using a small, angular paintbrush, do wall brushwork in areas where your roller can’t reach, like the corners and next to doors, windows and molding. If necessary, apply a second coat Beloit WI 53511 of paint using the same technique as the first. You don’t have to let the paint completely dry between coats, but your results will be better the longer you wait. Step 5: Clean Up   Use a shop vacuum to clean up dust and debris. Pick up your drop cloths or tarps and close up your paint cans. Dispose of used paint cans appropriately. Cleaning paintbrushes and other tools can Beloit WI 53511 be made easy with warm and soapy water. Thoroughly rinse your roller covers and brushes in water until the water runs clear, and then place them in a brush/roller spinner, if you have one, to remove excess liquid. Store in their protective sleeves or hang them on nails or hooks. Pick up drop cloths carefully, making sure not to spread around any paint that may have gotten on them. Remove Beloit WI 53511 painter’s tape at a 45-degree angle to avoid damaging any fresh paint. Remember that the longer it stays on, the harder it is to remove. Great job! You’ve withstood water damage and repaired your wall/ceiling. Related Posts & Videos

Video: Iphone 6 dead, board repair, water damage, shorted Vbat

Video: iPhone Water Damage Repair With Ultrasonic

Video: Attempted repair of Flooded E32 E-Box (Motronic ECU Water Damage)

Video: Asphalt Shingle Roofing Water Damage Repair

Video: How To Repair a Water Damaged Plasterboard / Drywall Ceiling

Video: How to use rice to repair water damage on iPhones and Macbooks

Business Results 1 - 10 of 8

Aurum Contracting
3 Reviews
Roofing, Siding, Damage Restoration
901 Elmwood Ave, Beloit, WI 53511

Furniture Medic by Lars
1 Reviews
Furniture Reupholstery, Furniture Repair, Damage Restoration
7634 La Harve Dr, Rockford, IL 61103

Micro-Green Restoration & Services
0 Reviews
Damage Restoration
Rockford, IL 61103

Shamrock Construction
3 Reviews
Contractors, Roofing, Painters
5512 Clayton Cir, Roscoe, IL 61073

Badger Basement Systems
6 Reviews
Waterproofing, Damage Restoration
N1656 US Hwy 12, Fort Atkinson, WI 53538

ServiceMaster Restoration
0 Reviews
Carpet Cleaning, Home Cleaning, Damage Restoration
600 Nathan Ln, Elkhorn, WI 53121

Zander Solutions
5 Reviews
Contractors, Waterproofing, Masonry/Concrete
421 S Nine Mound Rd, Verona, WI 53593

Smart Tech Repair
54 Reviews
IT Services & Computer Repair, Electronics Repair
204 E Golf Rd, Arlington Heights, IL 60005


For quality workmanship and service for your residential and commercial Water Damage needs, choose a company with over 38 years of service in the Beloit area.

Highly Rated

Integrity, quality workmanship and attention to detail have made us one of the most reliable Water Damage companies in Beloit.

Quality Service

We focus on making the process as least disruptive as possible to our clients

Affordable Prices

We work hard to keep our costs low and transfer these efficiency savings on to our customers

100% Wisconsin Licensed Experts

We can complete any size project  in a timely manner, without skipping any steps  or cutting any corners.


(877) 534-6458